- Shah Alam Selangor Malaysia
Working Location
Job Description
Responsibilities
The Project Engineer supports the Project Manager in executing fuel gas metering, pressure reduction & metering station (PRMS) and fuel gas train / conditioning packages, from contract award through engineering, procurement, fabrication, FAT, installation, commissioning and handover. The role owns the day-to-day engineering, document, procurement and site coordination work on assigned projects, so that each package is delivered safely, to specification, on schedule and within budget.
DUTIES & RESPONSIBILITIES OF THIS ROLE
A. Project Execution Support
1. Support the Project Manager in day-to-day execution of assigned projects, and take ownership of defined work packages (e.g. a skid, a metering run, a procurement package or a site activity) from start to finish.
2. Prepare and update the detailed project schedule (Primavera P6 / MS Project), 2–3 week look-ahead plans and progress S-curves, and flag slippage to the Project Manager early.
3. Coordinate daily with the in-house engineering, fabrication, QA/QC, procurement and site teams, and with the client, consultants, gas transporter / utility, vendors, sub-contractors and local authorities.
4. Prepare project deliverables to client requirements, including progress reports, minutes of meeting, technical queries (TQs), deviation requests, transmittals and the MDR / VDRL status register.
B. Engineering & Technical Deliverables – Fuel Gas Metering & Fuel Gas Train
5. Prepare or check engineering documents, including P&IDs, GA and isometric drawings, equipment and instrument data sheets, line / valve / instrument lists, cause & effect charts and bills of materials, working with the design engineers.
6. Perform or verify sizing calculations under the Project Manager’s review: meter sizing and run lengths, pressure regulator and control valve sizing (Cv), relief valve sizing, filter / separator sizing, Joule-Thomson cooling and heater duty, and line velocity / noise checks.
7. Specify and review equipment for the fuel gas train: inlet ESD / isolation valves, filter-separators, gas heaters, pressure regulators (active / monitor), slam-shut and creep relief valves, pressure safety valves, double block-and-bleed valves, and pressure / temperature transmitters.
8. Specify and review metering system equipment: ultrasonic, Coriolis, turbine, rotary or orifice meters, flow computers, gas chromatographs, moisture / H2S / dew point analysers and sampling systems, and their SCADA / DCS / RTU interface (Modbus, OPC).
9. Review vendor drawings, data sheets and calculations against the specification and applicable codes (e.g. AGA 3/7/8/9, ISO 5167, ISO 17089, EN 334, EN 14382, API 520/521, ASME B31.3/B31.8, IEC 60079, PETRONAS Technical Standards (PTS) and client technical requirements), and track comments to closure.
10. Prepare inputs for HAZID, HAZOP and constructability reviews, record actions, and raise design changes through the Management of Change (MOC) process.
C. Procurement & Cost Control
11. Prepare technical requisitions and purchase specifications; obtain quotations and prepare technical bid evaluations for the Project Manager’s approval, sourcing competitive but reliable equipment, bulk materials and consumables.
12. Expedite vendors and long-lead items (meters, GCs, analysers, regulators, ESD valves, heaters), and track delivery against the schedule.
13. Track committed and actual costs against the project budget; identify and record scope changes and prepare supporting documents for variation orders and progress claims.
14. Verify sub-contractor quantities and work done for progress claims.
D. Inspection, Testing, Site & Commissioning
15. Prepare Inspection & Test Plans and FAT / SAT procedures; coordinate and attend vendor inspections, hydrostatic / pneumatic and leak tests, meter calibration and FAT, and close out punch items.
16. Assist the Project Manager in executing site installation, mechanical completion, pre-commissioning, nitrogen purging, gas-in and commissioning, including regulator and slam-shut set-point checks, loop checks and metering system verification.
17. Supervise sub-contractors on site in line with method statements, permit-to-work and the approved drawings, and report progress and issues daily.
18. Compile as-built drawings and the final data book / MDR (calibration certificates, test records, material certificates and O&M manuals) for handover.
E. HSE, Quality & Compliance
19. Comply with and promote OSHA 1994 (as amended), DOSH requirements, client site HSE rules, permit-to-work, risk assessments (HIRARC), method statements and gas-in procedures.
20. Implement the project quality plan, raise and close NCRs, and prepare documents for regulatory submissions and approvals (e.g. Suruhanjaya Tenaga, DOSH, BOMBA) as instructed by the Project Manager.
21. Any other tasks assigned by the Project Manager.
EDUCATION & PROFESSIONAL QUALIFICATIONS
Essential
1. Bachelor’s degree in Mechanical, Chemical, Electrical or Instrumentation & Control Engineering, or an equivalent qualification.
Preferred
1. Graduate Engineer registration with the Board of Engineers Malaysia (BEM), working towards professional registration (Ir.).
2. Valid CIDB Green Card and NIOSH Safety Passport (or the client’s equivalent).
3. Training in flow measurement, pressure regulation, or hazardous area equipment (e.g. CompEx).
SKILLS AND EXPERIENCES
Essential
1. At least 3 years of engineering or project experience in oil & gas, gas utilities, power generation or process industries, including at least 2 years on gas metering, pressure regulating or fuel gas skid packages.
2. Working knowledge of fuel gas train equipment: control valves, pressure regulators, slam-shut and pressure safety valves, filters, gas meters, and pressure / temperature transmitters.
3. Ability to read and check P&IDs, GA and isometric drawings, data sheets and vendor documents, and to perform basic sizing calculations.
4. Hands-on involvement in FAT, site installation or commissioning of pressurised gas systems.
5. Ability to prepare and monitor a project schedule (Primavera P6 or MS Project); proficient in Microsoft Office and AutoCAD.
6. Good written and spoken English and Bahasa Malaysia; good communication and interpersonal skills with clients, vendors and sub-contractors.
7. Willingness to travel and to work on site, including outside normal hours during commissioning.
Preferred
1. Experience with fiscal / custody transfer metering systems, flow computers or gas chromatographs.
2. Experience on projects for Petronas Gas, Gas Malaysia, PETRONAS operating units or EPCC contractors under PTS.
3. Knowledge of skid fabrication, pressure equipment fabrication (ASME), welding and NDT.
4. Familiarity with SCADA / DCS integration and instrument loop checks.
Pay: RM3,500.00 - RM5,000.00 per month
Benefits:
Work Location: In person
Important Information
Never provide your bank or credit card details when applying for jobs. Do not transfer any money or complete unrelated online surveys. If you see something suspicious, Report this Job ad.