- Woodlands North Region (Singapore) Singapore
AXIOM RISE CONSULTANCY PTE. LTD. Hiring! Full Time TEST ENGINEER- RF in North Region (Singapore), Earn up to SGD 8,000 - Ricebowl
Share
Save
Working Location
Job Description
Responsibilities
Job Description
Work with test setup such as PNA-X, PXA, network analyzers, noise figure measurement, sophisticated system tools such ET/DPD, system alignment, transceiver optimization as well as antenna tuners to optimize the performance
Collect and evaluate data to verify performance over temperature, Voltage and process corners
Summarize and create performance reports
Characterization Report includes all the parametric data from RFFE such as Rx path NF, noise circles, IP2/IM2, IP3/IM3, Gain modes, S-parameters of Rx path components, as well as Tx path PAE, Gain, ACLR, power sweep, Rx Band Noise, Spectrum Emission Mask, s-par, x-par, Load-pull, Out-of-band rejection, frequency sweep, etc.
Bench HW & SW development for characterization test
Develop Characterization Test Plans to report the performance of RFFE products in a highly automated RF test set-up
Design and develop engineering evaluation test boards for RFFE products. Test board and RFFE module assembly (soldering)
Select, implement, and maintain test equipment necessary for RFFE product characterization
Work with RFFE Module and IC design team to maintain, optimize, and release chip setting for overall optimized product performances.
Job Requirements:
Bachelor's degree in Electrical Engineering, RF Engineering, Wireless communication or related field.
Preferred Qualifications
Knowledge of RF measurements such as S-parameters, P1dB, IP2/IP3, ACPR, NF, phase noise, ACLR, POUT, EVM, Harmonics
Knowledge of wireless communication protocol, such as GSM, WCDMA, LTE ,5G and GPS
Knowledge of different type of RF systems
Experience with LabVIEW programming, NI Test stand and NI equipment application
Experience with lab instruments/tools application (Oscilloscope, Spectrum analyzer, IQview, DMM, Network Analyzer, Signal Generator, etc.)
Experience with software programming, VBA, Python
Experience with RF, Mixed-signal PCB design and RF tuning
Knowledge of mixed-signal ADC, DAC, PMIC measurements such as INL, DNL, SNR, THD, SFDR, efficiency is preferred
Work with test setup such as PNA-X, PXA, network analyzers, noise figure measurement, sophisticated system tools such ET/DPD, system alignment, transceiver optimization as well as antenna tuners to optimize the performance
Collect and evaluate data to verify performance over temperature, Voltage and process corners
Summarize and create performance reports
Characterization Report includes all the parametric data from RFFE such as Rx path NF, noise circles, IP2/IM2, IP3/IM3, Gain modes, S-parameters of Rx path components, as well as Tx path PAE, Gain, ACLR, power sweep, Rx Band Noise, Spectrum Emission Mask, s-par, x-par, Load-pull, Out-of-band rejection, frequency sweep, etc.
Bench HW & SW development for characterization test
Develop Characterization Test Plans to report the performance of RFFE products in a highly automated RF test set-up
Design and develop engineering evaluation test boards for RFFE products. Test board and RFFE module assembly (soldering)
Select, implement, and maintain test equipment necessary for RFFE product characterization
Work with RFFE Module and IC design team to maintain, optimize, and release chip setting for overall optimized product performances.
Job Requirements:
Bachelor's degree in Electrical Engineering, RF Engineering, Wireless communication or related field.
Preferred Qualifications
Knowledge of RF measurements such as S-parameters, P1dB, IP2/IP3, ACPR, NF, phase noise, ACLR, POUT, EVM, Harmonics
Knowledge of wireless communication protocol, such as GSM, WCDMA, LTE ,5G and GPS
Knowledge of different type of RF systems
Experience with LabVIEW programming, NI Test stand and NI equipment application
Experience with lab instruments/tools application (Oscilloscope, Spectrum analyzer, IQview, DMM, Network Analyzer, Signal Generator, etc.)
Experience with software programming, VBA, Python
Experience with RF, Mixed-signal PCB design and RF tuning
Knowledge of mixed-signal ADC, DAC, PMIC measurements such as INL, DNL, SNR, THD, SFDR, efficiency is preferred
Important Information
Never provide your bank or credit card details when applying for jobs. Do not transfer any money or complete unrelated online surveys. If you see something suspicious, Report this Job ad.
Learn More