About the Role
Install, configure, test, and commission all cooling and thermal management systems within modular data centre units — including precision air conditioning, in-row cooling, adiabatic systems, and associated pipework and controls — ensuring each module achieves the specified thermal performance prior to dispatch.
Reports to: Mechanical Supervisor
KEY RESPONSIBILITIES
- Interpret cooling schematic diagrams, P&IDs, and refrigerant circuit diagrams for each MDC module configuration.
- Install, position, and mount CRAC and CRAH units, in-row coolers, rear-door heat exchangers, and adiabatic pre-cooling units per layout drawings.
- Carry out copper pipe fabrication and brazing, or press-fit connections, for DX refrigerant circuits and chilled water pipework loops within the module.
- Perform pressure testing, nitrogen purging, evacuation (deep vacuum), leak testing, and refrigerant charging on DX systems in compliance with DOE Malaysia / ASHRAE 15 requirements.
- Install and connect cooling control panels, BMS sensors (supply/return temperature, humidity, dew point, differential pressure), and actuated valves.
- Commission variable-frequency drive (VFD) fan arrays, EC fan motors, and cooling control systems; verify set-points, alarm thresholds, and control sequences per customer specification.
- Conduct thermal performance validation tests including airflow measurement (anemometer / airflow hood), temperature mapping, and delta-T verification across IT load simulation.
- Install coolant distribution units (CDUs), rear-door heat exchangers (RDHx), and manifold-based rack liquid distribution systems where specified; perform leak testing and flow balancing on liquid cooling loops.
- Diagnose and rectify faults during FAT including refrigerant undercharge, air-lock in chilled water circuits, sensor offset, and control logic errors.
- Maintain refrigerant handling logs and refrigerant register as required by Malaysian Department of Environment (DOE) and manufacturer warranty obligations.
- Support the Mechanical Fitter on pipe spool assembly and equipment positioning tasks.
- Complete test records, commissioning checklists, and handover documentation for each module.
REQUIREMENTS
Qualifications & Education
- Diploma or Degree in Mechanical Engineering, Refrigeration and Air Conditioning, or Building Services Engineering.
- SKM Level 3 in Refrigeration and Air Conditioning Technology may be accepted instead of a Diploma with at least 4 years of proven hands-on experience.
Relevant Experience
- At least 5 years of refrigeration, air-conditioning and data centre cooling installation and commissioning experience, OR at least 3 years with demonstrated experience focused on data centre precision cooling systems (CRAC / CRAH, in-row, DX, chilled water or liquid cooling).
- Experience with CDUs, RDHx or manifold-based liquid distribution is highly valued. Experience commissioning EC fan technology and reading fluid-system P&IDs is an advantage.
Technical Skills & Knowledge
- Copper pipe fabrication and brazing, press-fit connections (Viega / Parker) and flanged connections.
- Use of vacuum pumps, manifold gauge sets, refrigerant recovery / charging stations and electronic leak detectors.
- Familiarity with precision-cooling brands such as Vertiv (Liebert), Schneider Electric (APC), Stulz, Emerson or equivalent.
- Working knowledge of ASHRAE Thermal Guidelines for Data Processing Environments (A1–A4).
- Ability to read cooling-control logic and PLC / CRAC controller parameters.
- Practical knowledge of liquid-cooling systems, including direct-to-chip / cold-plate CDUs, rack manifolds, RDHx and single-phase immersion cooling tanks.
- Understanding of pressure drop, flow balancing, pump sizing and fluid quality management, including glycol concentration, pH and inhibitor levels.
- Knowledge of free-cooling and adiabatic-assist cycles is an advantage.
Licenses & Certifications
- Refrigerant Handling Certificate recognised by DOE Malaysia (F-Gas equivalent) - Mandatory
- Copper pipe brazing / flame certificate - Mandatory
Language & Other Requirements
- Bahasa Malaysia and English for technical documents and safety communication.
- Must be flexible to support overtime and shift commissioning windows, including on-call availability during FAT periods.
Pay: RM2,500.00 - RM4,500.00 per month
Benefits:
License/Certification:
- F-Gas / Refrigerant Handling Certificate (Required)
- Copper Pipe Brazing / Flame Certificate (Required)
Work Location: In person